Flashing

Shiny House, “Neckdowns,” Things Exterior

Welcome back to the journal, dear reader. In my last entry, I reported that Hale County had entered a state of oppressive heat and humidity. Several weeks have passed since that report, and climatically, nothing has changed. It’s 95oF in Hale County today, but they say it feels like 106oF. Let me ask you, dear reader, that if it feels like 106, then is it not 106? Alas, my mind wanders. Such a question is a trifle in comparison to my duty to you, that is to recount in an earnest fashion, the activity of Reverend Walker’s Home team.

While the environment is still and sweltering, my crew is the opposite. Intrepid and strong, and with the help of a protective roof, they carry on. I will admit, this motley crew are always raising the bar. I previously issued orders for them to complete the exterior of the home in a timely manner, and that they have. It was not a trivial amount of work. The tasks were varied and many. But yet again, the team has risen to the occasion. Doors and windows were built and installed concurrently with the application of siding and flashing. With additional help from new students during “Neckdown” Week, roll roofing was installed, the site was graded, beneath-ground drains installed, and a small patio built.

Doors & Windows

As Addie and Becca finished windows in the woodshop, Paul and George would install them on site. The whole unit is fabricated in the shop, making installation quick and easy. Pre-hung doors were installed and custom trim applied to the face of them to match the window details. As the doors and windows went in the house, siding and flashing were installed as allowed by what openings were done.

Siding

Reverend Walker’s Home is clad in the same galvalume r-panel that makes up the roof. Large, cut to length sheets make a fairly easy process. The only tricky parts are at those window locations where c-shapes need to be made out of the sheet metal. Bottom flashing was installed prior to siding.

leveling bottom flashing
installing r-panel
sided wall

Flashing

After the siding was put up, metal flashing and trim were next. The corner trim was installed first and then the top of wall flashing. The typical metal building corner trim has always been a team favorite. It is incredibly easy to install and is so big that it somehow disappears, or appears as just another ridge in the r-panel. Thank you fat corner trim. Top flashing was trickier with the different angles and cuts needed to make crisp connections between pieces. But with some practice cuts and good measurements it came together without much trouble.

cutting flashing with an angle grinder
flashed, trimmed, capped

Roofing

As flashing wrapped up, “Neckdown” Week began. Each day we were assisted by one or two new arrivals, bright-eyed and incredibly clean. We were also able to welcome Becca and Addie back from their shop sabbatical/site hiatus! Reunited and reinforced, we set about our work. Becca and Addie led the charge on the application of asphalt roll roofing to the top of the volumes. The roofing provides the final layer of water protection to the two volumes underneath the roof.

roofing layed out

Fireplace Patio

As the roll roofing went on, Paul and George were joined by several Landscape Architecture students, who offered advice and assistance in making a small gravel patio. After a quick design discussion, the area was graded, and a first length of French drain was installed so that we could move forward with edging and infilling with gravel. The rest of the drain would be installed later.

relax

Grading

When the roofing and patio jobs were complete, it was all hands on deck for site grading. With the help of the skid-steer, earth was moved from the excavated pile to the slab edge and graded away. Additionally, several large ruts were filled in and the site was smoothed out. The septic mound was extended with any remaining earth in the pile.

So, post grading, what we are left with is a mostly finished exterior of a house. There are always a few odds and ends to take care of, but there is no doubt that “Neckdown” Week was a huge success on site.

Certainly, much has happened in a short period of time. I tell you once more, dear reader, that this bunch is special. Of course this is not to say that it could have been done without my strong leadership. It takes a steady paw to guide a vessel this size through choppy waters. On the horizon I see finish carpentry, plumbing, electrical, and other odds and ends. I will continue to record the progress of Reverend Walker’s Home for posterity, the world deserves to know the intricacies of our grand adventure. Alas, dear reader, the sun draws closer to the horizon and I have grown weary. I must put aside my journal in favor of a nap. I think I will chose a nice spot in between two elephant ears Paul has acquired for this occasion.

Yours sincerely,

Taterhead

Weather Proof and a Roof

Live from the Test Buildings, it’s the Thermal Mass and Buoyancy Ventilation Research Project team. After swiftly assembling the Test Buildings, the graduate team began weatherproofing. The team’s goal is to have the buildings protected from rain quickly so they can get to work on installing the thermal mass panels on the interior. The weatherproofing systems are designed to mitigate heat gain in different ways to eliminate experimental variation.

First, the team covered the buildings in shingled tar paper–a heavy-duty, waterproof construction paper. Next, the team installed battens which create space between the structure and cladding allowing for ventilation and avoiding heat gain. The roof is also ventilated and covered with highly reflective, low albedo corrugated sheet metal. This means the materiality and color of the roof are fighting solar radiation.

Lastly, the team installed the beautiful steel door frames. Turnipseed International donated the steel and Brad of Superior Metals LLC welded the frames Thanks for reading and stay tuned.

Tar Paper and Battens

Roof Battens and Flashing

Roofing Metal

Both roofs complete!

Door Frame